User’s GuideSlide Feeder for Flextight 949 Scannersby Hasselblad
10 AB Figure 3: Back panel of the Slide Feeder, showing the electrical connector (A) and mounting pins (B).Li the batch-feeder panel on the front of
11Grasp the Slide Feeder rmly with one hand while holding the batch-scan door open on the scanner with your other hand. Align the pins and connector
12 BACD Figure 5: e Slide Feeder attached to a scanner and with its magazine drawer open, showing the original-holder supports (A), drawer hinge (B),
13 Figure 6: Inserting the Slide original holder.Position the Slide holder on the two supports extending from the front of the Slide Feeder and slide
14Click on Done to close the Feeder window.Close the magazine drawer by rotating it up and pressing it into place so that the metal clasp clicks in it
15Unmounting the Slide FeederTo unmount the feeder, you must always use the soware-guided procedure below to ensure that the scanner drum and the mag
16e Mount feeder window updates with new instructions. As instructed in the window, remove the holder from the scanner with both hands, grasping the
17e Mount feeder window updates with new instructions. Close the magazine drawer by rotating it up and pressing it into place so that the metal clas
18Loading SlidesDepending on your work load and preferred working method, you might decide to load slides directly into the Feeder, or to work using t
19Remove any slides that you have already scanned. en, starting at the front/top of the magazine, load new slides in the order in which you would lik
2© 2005 Hasselblad A/S. All rights reserved.Slide Feeder for Flextight 949 Scanners, Part No 75020088 revision B.e information in this manual is furn
20 Figure 10: Removing the magazine drawer from its hinge.Place the drawer at on a table with its magazine facing up.Using both hands, pinch the four
21Take the second magazine, which you just nished loading, and position it the same way as the magazine you just removed. At one end, the magazine ha
22Scanning with the Slide FeederBatch Scanning with 3fe Slide Feeder is intended as a tool for scanning large number of slides in a production enviro
23Instead of using the standard preview/scan workow in FlexColor, click on the 3f button to open the Scan 3f window. Make the various 3f settings as
24FlexColor to analyze each image to decide whether it is negative or positive. It will then use either the Positive Setup or Negative Setup that you
25As you work with the 3f images in the light table, you can load each image into FlexColor to make settings and then save the settings back in the hi
26Click on the Batch Scan button to open the Batch Scan window.If it is not already shown, expand the Feeder heading in the Batch Scan window by click
27 If you are using the Manual list, then continue taking previews and adding scans until you have dened all of the scans you wish to make in this ba
28TroubleshootingBelow are a few common problems and how to solve them.Problem: I am not able to mount the Feeder to my scanner.Solution: First, mak
29Solution 2: Move the drum to its home position. To do this, run FlexColor and select Maintenance > Feeder to open the Feeder window. en set the
3Table of ContentsIntroduction 4Important Warnings and Restrictions 4System Requirements 5Feeder Diagram 6Slide Original Holder Diagram 7Mounting
30Aligning the Feedere Feeder is pre-adjusted to align perfectly with most individual scanners. However, some scanners may have a drum that is aligne
31 Figure 13: Unlocking/locking the Feeder position. Two nuts hold the Feeder in place—one is visible above; the other is located on the other side of
32Preparing the Slide Feeder for Storage or TransportTo prepare the Feeder for storage or transportation:Detach the Feeder using the soware-guided pr
33Preventive MaintenanceAll Flextight scanners should be serviced every 25,000 scans or every 12 months, whichever comes rst. If a Feeder is mounted,
34Technical InformationSpecicationsScanner supported Flextight 949Scanner footprint with feeder 36 x 42 cmWeight 3.1 kgMaximum batch 50 slidesOri
35CE Declaration
4Introductione Slide Feeder is an optional accessory for Flextight 949 Scanners. It enables you to use your scanner to load individual slides and to
5Install the scanner and Slide Feeder in a location where they are not accessible by children. e units contain small openings and moving parts that c
6Feeder DiagramACDFBEG Figure 1: Features of the Slide FeederMagazine drawer clasp: holds the drawer closed; to open the drawer, pull here and swing d
7Slide Original Holder DiagramACDEFB Figure 2: Slide original holder featuresLoading tab: is tab must face into the scanner. A magnet inside the scan
8Mounting and Unmounting the Slide Feedere procedures for both mounting and unmounting the Feeder to/from your scanner require that you use the sowa
9Select Maintenance > Feeder from the FlexColor menu bar. e Feeder window opens. Click on the Mount button. e Mount feeder window opens, which g
Kommentare zu diesen Handbüchern