User’s GuideBatch Feeder for Flextight 848 and 949 Scannersby Hasselblad
10Get the Batch Feeder and study its back panel. Here you should see an electronic connector (A) and a pair of mounting pins (B), as shown in Figure 3
11Grasp the Batch Feeder rmly with one hand while holding the batch-scan door open on the scanner with your other hand. Align the connector and pins
12Unmounting the Batch FeederAlways use the soware-guided procedure below to unmount the Feeder. It is otherwise possible to damage the Feeder and/or
13e scanner shuts down and the Mount feeder window updates with new instructions. If there are original holders in the magazine, then remove them al
14Loading Originals into the FeederCPos. 1Pos. 10AB Figure 5: Loading originals into the FeederTo load originals into Batch Feeder, refer to Figure 5
15Continue loading originals into holders and holders into the scanner until you have either loaded all of your originals or used all 10 slots of the
16Scanning with the Batch FeederBatch Scanning with 3fe Batch Feeder is intended as a tool for scanning large numbers of originals in a production en
17Instead of using the standard preview/scan workow in FlexColor, click on the 3f button to open the Scan 3f window. Make the various 3f settings as
18If you have both negative and positive originals in your batch, you should set Film Type to “Auto Detection”. is will cause FlexCol-or to analyze e
19As you work with the 3f images in the light table, you can load each im-age into FlexColor to make settings and then save the settings back in the h
2 © 2005 Hasselblad A/S. All rights reserved. Feeder for Hasselblad Flextight 848 and 949 Scanners User’s Guide, Part No 70030031, revision E. e in
20If it is not already shown, expand the Feeder heading in the Batch Scan window by clicking on the triangle next to the heading. Set the Position e
21 If you are using the Manual list, then continue taking previews and adding scans until you have dened all of the scans you wish to make in this ba
22TroubleshootingBelow are a few common problems and how to solve them.Problem: e Feeder is not recognized by the scanner or FlexColor soware.Solut
23Aligning the Feedere Feeder is pre-adjusted to align perfectly with most individual Flex-tight 848 and 949 Scanners. However, some scanners may hav
24 Figure 6: Adjusting the Feeder angleIf the Feeder looks to be hanging evenly on both the le and right sides, then you are done. Skip the rest of t
25 Figure 7: Bolts for adjusting the feeder angleUse your ngers to turn the two adjustment bolts until that they look as though they will hold the bo
26Find the adjustment tool that was supplied with your Batch Feeder. It is a thin metal bar with notches cut at each end.Use the adjustment tool to lo
27Click on the Align Feeder button. e Align Feeder window opens, which will now guide you through the procedure of aligning the feeder. You have alr
28 Figure 9: Using the adjustment toolMove the adjustment tool le and right to adjust the Feeder position so the Feeder is centered with reference to
29e scanner now shuts down and the Align Feeder window updates with new instructions. Remove the Feeder and use the adjustment tool to re-tighten th
3Table of ContentsIntroduction 4Important Warnings and Restrictions 4System Requirements 5Batch Feeder Diagram 6Preparing the Feeder for First Use
30You now return to the Feeder window. Click on Done to close the Feeder window.Load original holders into all 10 original holder slots and then sca
31Preparing the Feeder for Storage or ShippingStoring the FeederTo store the Feeder while it is not in use:Detach the Feeder using the soware-guided
32Examine the bottom of the back side of the Feeder and locate the two holes used to secure the magazine during shipping (see Figure 11, below). Inser
33Preventive MaintenanceAll Flextight scanners should be serviced every 25,000 scans or every 12 months, whichever comes rst. If a Feeder is mounted,
34Technical InformationSpecicationsScanners supported Flextight 848 and 949Scanner footprint with feeder 36 x 42 cmWeight 3.1 kgMaximum batch 10
35CE Declaration
36
4Introductione Batch Feeder enables you to load up to 10 original holders (up to 60 originals, depending on format) for batch scanning with your Flex
5When you switch on the scanner, the Feeder will position itself into its “home” position, if not already there. Do not touch the Feeder while the mag
6Batch Feeder DiagramABFGHCDEFigure 1: Hasselblad Flextight 848 Scanner with Batch FeederHasselblad Flextight 848 (or 949) Scanner.Batch FeederDust co
7Preparing the Feeder for First Use or after ShippingBefore you begin to use the Feeder, you must remove the two shipping screws that secure the magaz
8Mounting and Unmounting the Batch Feedere procedures for both mounting and unmounting the Feeder to/from your scanner require that you use the sowa
9e Feeder window opens. Click on the Mount button. e Mount feeder window opens, which guides you through each step of mounting the Feeder. e proce
Kommentare zu diesen Handbüchern